湿度对水泥生料近红外光谱检测的影响及补偿方法

近红外光谱检测已被应用于水泥生料成分的快速检测,但现场环境中的湿度等因素会对光谱产生干扰,从而降低检测精度。为了提高检测精度,在实验分析湿度对水泥生料近红外光谱检测影响的基础上研究了补偿方法。在水泥厂选取了24份水泥生料样本,其中18份作为校正集,6份作为验证集;水泥生料中的有效成分为SiO2,Al2O3,Fe2O3和CaCO3,各成分含量的标准值由X射线荧光光谱分析测出。首先,将校正集的18份样本每份重复装样测5次光谱,用得到的90个光谱建立模型Ⅰ;再每份样品制作5个湿度梯度样本,其获得过程为,先将样本放置在电加热平台上,用玻璃棒将样本摊平,180℃下加热30 min,再将样本放置在散热片上进行降温,待样品恢复室温后取出进行第一次光谱扫描,得到1个光谱,将测量后的样本放入搅拌器,使用装有去离子水的喷雾器对其喷雾两次,然后搅拌30 s混合均匀,测量混合后的样本得到下一个光谱,重复该过程,得到具有湿度梯度的5个光谱。所有样本均采用烘干法进行湿度测量,样本湿度变化区间在0.6%~2%以内。对每个湿度梯度的样本测量1次,用得到的这90个光谱建立模型Ⅱ。然后,将验证集的6份样本每份制作5个湿度梯度,获取方式与校正集相同,对每个湿度梯度的样本测量1次,得到30个光谱。所有光谱均采用多元散射校正预处理,拟合波段选择4000~5000 cm^-1,建模方法采用偏最小二乘法。比较同一份样本的5个湿度梯度,可以看到在5200 cm^-1处光谱差异最大,在其他位置也有肉眼可见的明显差异,因此,湿度变化对全波段光谱有明显的影响。最后,将这30个光谱输入模型Ⅰ与模型Ⅱ进行验证,并对比模型Ⅰ与模型Ⅱ的预测均方根误差RMSEP。模型Ⅱ中SiO2,Al2O3,Fe2O3和CaCO3的预测均方根误差RMSEP比模型Ⅰ分别减小了25%,31.3%,33.3%和25%。实验结果表明,水泥生料样本湿度对近红外光谱模型的预测结果具有一定的影响,采用具有湿度梯度的样本进行建模可有效降低湿度对预测结果的影响。     

Fluorescent macrocyclic chemosensor for Zn(II) detection at alkaline pH values

ABSTRACT

The new macrocyclic ligand L (28,29-dimethoxy-27-oxa-8,11,14,17,25,26-hexaazatetracyclo[22.2.1.1(2,6).1(19,23)]nonacosa-2,4,6(28),19,21,23(29),24,26(1)-octaene) has been synthesised. It contains a tetramine chain and the 2,5-bis(2-methoxy-3-metyl-phenyl)-1,3,4-oxadiazole (PPD-OMe) chromophore, acting as coordinating and sensing units, respectively.

The fluorescent emission of L depends on the pH being highly fluorescent at pH = 2 and not emitting from pH >10. The studies highlighted that L is a PET mediated emitting chemosensor, being the PET effect regulated by the degree of the tetraamine protonation.

L coordinates metal ions (Cu(II), Zn(II) and Cd(II)) in water giving rise to an OFF-ON fluorescent response for the presence of Zn(II) ion thus signalling its presence in the medium. This response is particularly notable at pH = 9 allowing to extend the Zn(II) sensing also in the alkaline pH field.     

小直径棒材超声横波检测仿真分析

采用超声水浸聚焦斜入射方式进行小棒材表面、近表缺陷检测时,声波在水/棒和棒/缺陷界面会发生反射、折射、散射、衍射及波形转换等一系列物理变换。此时缺陷可检性对声波入射条件十分敏感,常出现由于检测条件设置不当而导致缺陷漏检、误检的情况。为解决这一问题,本文针对小棒材超声斜入射检测中的主要参数——入射角和水距,开展声场及缺陷声响应仿真,研究检测参数对不同部位缺陷检测能力的影响,并对仿真结果进行试验验证。通过研究得到了检测水距、入射角度对缺陷检测能力的影响,并得到最优检测条件。试验验证结果表明研究制定的检测方案可有效检测出表面、近表面裂纹缺陷。     

Microstructure and dielectric study of pure BST and doped BSTF ceramic materials by broadband dielectric spectroscopy

Pure BST and doped BSTF (with BSTF2: Fe₂O₃ 2 wt % and BSTF4: Fe₂O₃ 4 wt %) ceramics were prepared by solid state reaction. XRD pattern showed the different phases were formed depend on the weight percent of Fe₂O₃. The crystal size and lattice parameters increased while the lattice strain decreased. The topography of the sintered samples shows increase of the grain size with increasing Fe₂O₃ ratio and hence enhances the compaction of ceramics. Broadband dielectric spectroscopy was employed to investigate the effect of magnetite nanoparticle on the dielectric properties of the pure BST ceramic. The interfacial polarization and the conductivity contribution reflect the high values of permittivity and its gradual increase as frequency decreases. The two BSTF samples show relaxation peak dynamic originated from presence of immobile species/electrons at low temperatures and defects/vacancies results from the formation of oxygen vacancies originates from the spontaneous change in oxidation states of Fe ions (Fe ^3+/Fe²⁺) at high temperatures. The relaxation rate obeys Arrhenius law at high temperatures in case of BST sample with activation energy 225 kJ/mol. This high value of activation energy at higher temperatures reflects and confirms the slowed down of the dynamics at the interphase and the decoupling nature of the OH-dynamic and the interfacial polarization.     

基于科赫曲线分形结构太赫兹带通滤波器

太赫兹滤波器是太赫兹通信、太赫兹成像和太赫兹检测等太赫兹应用系统中不可或缺的功能器件。按照不同的分类方式,滤波器有不同的种类,常见的按照选频功能可分为高通滤波器、低通滤波器、带阻滤波器和带通滤波器。为了实现在太赫兹波段的滤波效果,世界各地的研究人员利用不同的结构、材料和控制方式实现了功能各异的太赫兹滤波器,但是考虑到设计的器件要应用到太赫兹系统中,成本低廉、结构简单、性能优越的太赫兹滤波器一直是研究人员的追求。分形概念自提出以来在很多研究领域都有了快速发展,但是在太赫兹波段的应用还不是很常见,特别是应用于太赫兹功能器件的设计。引入分形中科赫曲线的概念设计并制备了一种新型的太赫兹带通滤波器,该滤波器是在金属薄膜上刻蚀出科赫曲线分形结构,当太赫兹波垂直入射到该滤波器时候实现了在太赫兹波段的窄带滤波。在滤波器的设计过程中,追求理论与实验相结合,首先在电磁仿真软件中建立科赫曲线分形结构滤波器模型进行计算,探究分形结构应用于太赫兹波段进行滤波的可行性,在进行多次计算之后得到优化后的尺寸和结构,然后根据优化后的尺寸加工出科赫曲线分形结构太赫兹滤波器样品,并且将样品放在太赫兹时域光谱系统中进行实验测量,得到实验数据后与仿真结果进行比较。在仿真中利用了时域有限差分法模拟科赫曲线分形结构太赫兹带通滤波器的传输特性,优化后的仿真结果表明:滤波器的谐振频率为0.715 THz,透射系数能够达到0.92,-3 dB带宽为21.9 GHz,将仿真得到的散射参数进行S参数反演得到了太赫兹滤波器样品的电磁参数,这在理论上分析了太赫兹波在谐振点处产生透射增强的原因。利用飞秒激光微加工系统制备了尺寸优化后的科赫曲线分形结构太赫兹带通滤波器样品,然后使用太赫兹时域光谱系统对样品的传输特性进行测试,对实验得到的时域数据进行快速傅里叶变换之后得到频域数据,再把频域数据进行归一化处理后与之前的电磁仿真结果进行对比,发现实验测得的结果与电磁软件仿真得到的结果较为吻合。     

Ultrasensitive determination of mercury by solution anode glow discharge atomic emission spectrometry coupled with hydride generation

An innovative method for the ultrasensitive detection of mercury by solution anode glow discharge atomic emission spectroscopy (SAGD-AES) coupled with hydride generation (HG) was first investigated. In this method, the mercury vapor generated by the HG was transmitted to the SAGD through the miniature hollow tungsten tube for excitation and detected by a miniaturized spectrograph. A thorough parametric evaluation of the HG and SAGD system was performed, including the type and concentration of carrier acid, He flow rate, concentrations of NaBH₄, discharge current and discharge gap. Under optimal operating conditions, the detection limit for Hg²⁺ achieved 0.03 μg/L, with a relative standard deviation of 1.1% at the Hg²⁺ concentration of 5 μg/L. Moreover, the correlation coefficient of the calibration curve was 0.9996 in the range between 0.1 and 10 μg/L. The accuracy and practicability of HG-SAGD-AES were verified by measuring GBW09101b (human hair), GBW10029 (fish), soil and rice samples. The results showed good agreement with the certified values and values from direct mercury analyzer (DMA).     

Sulfono‐γ‐AApeptides as a New Class of Nonnatural Helical Foldamer

Foldamers offer an attractive opportunity for the design of novel molecules that mimic the structures and functions of proteins and enzymes including biocatalysis and biomolecular recognition. Herein we report a new class of nonnatural helical sulfono‐γ‐AApeptide foldamers of varying lengths. The crystal structure of the sulfono‐γ‐AApeptide monomer S6 illustrates the intrinsic folding propensity of sulfono‐γ‐AApeptides, which likely originates from the bulkiness of tertiary sulfonamide moiety. The two‐dimensional solution NMR spectroscopy data for the longest sequence S1 demonstrates a 10/16 right‐handed helical structure. Optical analysis using circular dichroism further supports well‐ defined helical conformation of sulfono‐γ‐AApeptides in solution containing as few as five building blocks. Future development of sulfono‐γ‐AApeptides may lead to new foldamers with discrete functions, enabling expanded application in chemical biology and biomedical sciences.     

An experimental method for eliminating effect of rigid out-of-plane motion on 2D-DIC

The out-of-plane motion is one of the most important factors that affect the precision of two-dimensional digital image correlation (2D-DIC). In this paper, a novel solution is presented to improve conventional 2D-DIC by eliminating the effect of out-of-plane motion, including translation and rotation. Firstly, an experimental technique using two projected laser strips is proposed to measure the out-of-plane motion of a planar specimen. A theoretical model is then established to predict the pseudostrains caused by out-of-plane motion based on the pin-hole imaging model. Using the measured out-of-plane displacement, the captured deformed images used in 2D-DIC are amended to eliminate the effect of out-of-plane motion by the theoretical model. Finally, two experiments were conducted to validate the effectiveness of the proposed method. Results indicate that application of the proposed method can effectively eliminate the errors caused by out-of-plane motion.     

Insight into copper-mordenite–silica mixtures (CuMOR–SiO2)

A series of ternary CuMOR–SiO₂ mixed materials were prepared by two synthesis approaches (CuMOR1–y–SiO₂ and CuMOR2–y–SiO₂). Extensive characterization was done for both series and some selected materials were tested in CO catalytic oxidation and NO reduction. The presence of CuMOR and SiO₂ segregated phases was observed in both series by XRD, suggesting that silica formation was not inhibited by the mordenite (MOR) presence. UV–Vis results exhibited that Cu ion exchange was successfully done for CuMOR1–y–SiO₂ series. In the CuMOR2–y–SiO₂ series, the amount of copper was below the sensitivity limit of EDS analysis. CuMOR1–50%–SiO₂ catalyst resulted with higher specific surface area and catalytic activity. A possible relation between reduction temperature, the increase in Cu plasmon excitation, and catalytic activity was observed.     

Synthesis,Electrochemistry, and Photophysics of Aza‐BODIPY Porphyrin Dyes

The synthesis of dyad and triad aza‐BODIPY‐porphyrin systems in two steps starting from an aryl‐substituted aza‐BODIPY chromophore is described. The properties of the resulting aza‐BODIPY‐porphyrin conjugates have been extensively investigated by means of electrochemistry, spectroelectrochemistry, and absorption/emission spectroscopy. Fluorescence measurements have revealed a dramatic loss of luminescence intensity, mainly due to competitive energy transfer and photoinduced electron transfer involving charge separation followed by recombination.